The Jet Ski Doctor — Watercraft SpecialistThe Jet Ski DoctorWATERCRAFT SPECIALIST · SINCE 1992 954-914-6465

Guides · From the watercraft specialists

Salt-Away for Jet Skis: How to Use It (and Why a Fresh-Water Flush Isn't Enough)

Fresh water rinses salt water out. It doesn't dissolve the salt crystals already stuck inside your cooling passages and exhaust. That's what Salt-Away is for, and it's the product our techs use on skis across South Florida. Here's how to use it right.

Jet skis on a lift at a South Florida waterfront home

What Salt-Away does

Salt-Away is a concentrate that dissolves salt deposits and leaves a protective film that slows corrosion on metal. You don't pour it in: it goes through a mixing unit that screws onto your garden hose and blends it at the right ratio automatically (about 1 part concentrate to 512 parts water, so one 32 oz bottle goes a long way).

A plain fresh-water flush pushes salt water out. Salt-Away goes further: it breaks down the crust that builds up over many rides and protects the metal until the next one.

Which parts of your ski get salt water?

It depends on the cooling system, and this is where a lot of owners get confused:

  • Yamaha and Kawasaki (open-loop): the water you ride in runs through the engine block and the exhaust. Everything gets salt.
  • Sea-Doo (closed-loop): the engine block is cooled by sealed antifreeze, but the exhaust, and the intercooler on supercharged models, still use the water you ride in. Those parts still get salt, which is why Sea-Doos still need flushing after salt rides.

So no matter which brand you ride, if you ride in salt or brackish water, part of your ski is full of it when you get home.

Technician checking a jet ski engine bay for salt and corrosion

What you need

All of these are in our online shop. Not sure which adapter fits your model? Call or WhatsApp 954-914-6465 and we'll tell you.

How to flush with Salt-Away, step by step

The mixing unit has three positions: Off, Rinse (plain water) and Salt-Away. On most open-loop skis (Yamaha, Kawasaki):

  1. Screw the mixing unit onto the hose, set to Off, and connect the hose to the ski's flush port.
  2. Start the engine first and let it idle.
  3. Turn the tap on and set the mixing unit to Rinse. Let fresh water run through for about a minute.
  4. Switch to Salt-Away for the last part of the flush, about 10–20 seconds, until you see suds at the outlets.
  5. Set the mixing unit to Off (water first), give the throttle a couple of gentle blips to clear the water, then shut the engine off.
  6. Leave the Salt-Away inside. Don't rinse it back out: the film is what protects the metal.

Never run water into an open-loop engine that isn't running. It can back up and flood the engine. Water off before engine off, every time.

Sea-Doo: the flush procedure varies by model and year, so follow your owner's manual for when to start the engine and how long to run the water. Use the same mixing unit and finish on the Salt-Away setting.

Don't forget the outside

Salt-Away also works as a wash. Run the mixing unit on the Salt-Away setting with a spray nozzle over the hull, the pump and intake area, the engine bay (lightly, and never on the belts or air intake), the trailer and the lift. Salt crusts on clamps, bolts and the trailer are what quietly rust out first in South Florida.

How often should you use it?

  • Fresh-water flush: after every salt ride.
  • Salt-Away: ideally every salt ride too. At minimum, every few rides and always before the ski sits for more than a week or two.
  • Before storage: always finish with Salt-Away.

Let us handle it

Every Jet Ski Doctor membership visit includes a flush and an anti-corrosion treatment right at your dock. Want a Salt-Away kit? Grab the Salt-Away starter kit with mixing unit (32 oz) in our online shop, or ask and your tech can bring one on the next visit and show you how to use it on your ski.

Want us to take care of it?

Mobile jet ski service at your dock across Miami-Dade, Broward & Palm Beach — from South Florida's watercraft specialist since 1992.

Quick answers

What is Salt-Away used for on a jet ski?

Salt-Away dissolves salt deposits inside the cooling passages and exhaust and on the outside of the ski, then leaves a film that helps prevent corrosion. It's used during the flush, through a mixing unit on your garden hose.

Do I need Salt-Away if I flush with fresh water?

A fresh-water flush pushes the salt water out but doesn't dissolve salt crystals that have already built up. Salt-Away removes them and adds corrosion protection, so it's worth adding, especially in South Florida.

Do Sea-Doos need to be flushed if they have closed-loop cooling?

Yes. The engine block is cooled by sealed coolant, but the exhaust (and the intercooler on supercharged models) still uses the water you ride in, so it still needs flushing after salt rides.

Do I rinse Salt-Away out after the flush?

No. Finish on the Salt-Away setting and leave it in. The protective film is the point.

Where can I buy Salt-Away?

The Jet Ski Doctor sells the Salt-Away starter kit with mixing unit and refills in our online shop at shop.jetskidoctor.com, and members can ask their tech to bring one on the next visit.

Ready when you are

Let's get your ski running right.

Book a mobile visit online in under a minute — or call and talk to a real mechanic.

Call Book a visit